Call

 

What are your thoughts on Installing A Bathtub?

Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough job. If the old tub is readily accessible, the project can move easily; if you need to open a wall surface to remove the old bathtub and also position the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have qualified on your own for the work and are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to consider using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your washroom if you have actually currently acquired a new bathtub as well as don't need to transform the arrangement of your previous water system pipes.
Your tools as well as product list need to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome because of the restricted access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Secure the faucet in position with the producer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be connected to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Installing the Tub

Making use of both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bathtub up until the level checks out level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply as well as inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the tub as well as additionally inspect the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub should wait until the tub has actually been made use of at the very least once as this will certainly settle it right into its final placement.

 

 

Getting ready for the Installation

First of all, the sustaining structure provided with the bathroom should be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final position.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, creating the water to permeate the wall surface between the bathroom and also the tiling, causing problems with wetness and also possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bathtub with water prior to sealing, to enable the motion experienced when the tub is in usage. The sealer can split relatively early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or water resistant glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a serious reader on Installing A Bathtub, I assumed sharing that section was a great idea. Those who enjoyed our blog entry plz don't forget to share it. I praise you for your time. Visit us again soon.

Secure top-grade service.